厂商 ：常州蓝阳环保设备有限公司
江苏 常州- 主营产品：
- 活性炭吸附箱
- 废气处理设备
- 废气净化设备
联系电话 ：13179310883
商品详细描述
有机废气净化塔,有机废气处理塔,喷漆废气净化塔,盐酸废气净化塔 加工定制
蓝阳环保，咨询热线：0519-81668662，13179310883，欢迎您的来电垂询！~~
一、工作原理
酸雾废气由风管引入净化塔，经过填料层，废气与氢氧化钠吸收液进行气液两相充分接触吸收中和反应，酸雾废气经过净化后，再经除雾板脱水除雾后由风机排入大气。吸收液在塔底经水泵增压后在塔顶喷淋而下，最后回流至塔底循环使用。净化后的酸雾废气达到广东省地方排放标准的排放要求，低于国家排放标准。
二、特点
1.除尘脱硫效率高，采用碱性洗涤水时，脱硫效率可达85%；
2.设备占地少，安装方便；
3.耗水、耗电指标较低；
4.耐腐蚀、不磨损，使用寿命长；
5.设备运行可靠，维护简单、方便。
三、结构
喷淋塔内填料层作为气液两相间接触构件的传质设备。喷淋塔底部装有填料支承板，填料以乱堆方式放置在支承板上。填料的上方安装填料压板，以防被上升气流吹动。喷淋塔喷淋液从塔顶经液体分布器喷淋到填料上，并沿填料表面流下。气体从塔底送入，经气体分布装置分布后，与液体呈逆流连续通过填料层的空隙，在填料表面上，气液两相密切接触进行传质。当液体沿填料层向下流动时，有时会出现壁流现象，壁流效应造成气液两相在填料层中分布不均，从而使传质效率下降。因此，喷淋塔内的填料层分为两段，中间设置再分布装置，经重新分布后喷淋到下层填料上。
活性炭吸附装置（PP材质）
产品名称：活性炭吸附装置（PP材质）
产品型号：SYD-HXT
产品简介：
活性炭吸附塔，是一种高效率经济实用型有机废气的净化与治理装置；是一种废气过滤吸附异味的环保设备产品。
产品详情
活性炭吸附装置（PP材质）
活性炭吸附塔能对苯、醇、酮、觯、酯、汽油类等有机溶剂的废气吸附回收，更适用于小风量高浓度的废气治理，因此喷涂、食品加工、印刷电路板、半导体制造、化工、电子、制皮业、乳胶制品业、 造纸等行业均可选用. 活性炭吸附设备主要是利用多孔性固体吸附剂活性炭具有吸附作用，能有效的阹除工业废气中的有机类污染物质和色味等，广泛应用于工业有机废气净化的末端处理，净化效果良好。气体经管道进入吸收塔后，在两个不同相界面之间产生扩散过程，扩散结束，气体被风机吸出并排放出去.
Organic waste gas purification tower, organic waste gas treatment tower, painting waste gas purification tower, hydrochloric acid waste gas purification tower processing custom
First, the working principle
The introduction of acid mist exhaust purification tower by air duct, exhaust gas passes through the filler layer, and sodium hydroxide absorption liquid two-phase full contact absorption neutralization reaction, acid mist emissions after cleaning, the demisting plate dehydration fog by the fan into the atmosphere. The absorption liquid is sprayed at the top of the tower by a water pump, and then is sprayed down to the bottom of the tower. Acid mist emissions after purification reached Guangdong local discharge standard requirements, lower than the national emission standard.
Two, characteristics
1 the efficiency of dust removal and desulfurization is high, the desulfurization efficiency can reach to 85% when using alkaline washing water;
2 equipment area is small, easy to install;
3 water consumption, low power consumption indicators;
4 corrosion resistance, no wear, long service life;
5 the equipment is reliable and easy to maintain.
Three, structure
The spray tower filler layer as a component of gas-liquid two phase contact mass transfer equipment. At the bottom of the spray tower with packing support plate, packing to huddle place in the support plate. The filler is installed above the filler plate, in order to prevent rising air blowing. Spray tower spray liquid from the top of the tower by spraying liquid distributor to packing, and the packing surface along the flow. The gas is fed from the bottom of the tower, and is distributed with the liquid through the gas distribution device, and then flows through the gap of the packing layer. When the liquid flows along the packing layer, the wall flow phenomenon sometimes occurs, and the wall flow effect results in the uneven distribution of the gas-liquid two-phase in the packing layer, which leads to the decrease of the mass transfer efficiency. Therefore, the filler layer spray tower is divided into two sections, arranged in the middle of distribution device, the re distribution of spray to lower packing.
Activated carbon adsorption device (PP material)
Product Name: activated carbon adsorption device (PP material)
Item No: SYD-HXT
Product profile:
Activated carbon adsorption is an efficient purification tower, economical and practical organic waste and governance is a waste gas filtering device; adsorption odor environmental protection equipment products.
product details
Activated carbon adsorption device (PP material)
Activated carbon adsorption tower adsorption gas recovery of benzene, alcohol, ester, ketone, Zhi, gasoline and other organic solvent, is more suitable for small volume high concentration of exhaust gas, so spraying, food processing, printed circuit board, semiconductor manufacturing, chemical industry, electronics, leather, latex products industry, papermaking etc. the industry can be used. The activated carbon adsorption equipment is the use of porous solid adsorbent with activated carbon adsorption, in addition to Qu in industrial waste gas of organic pollutants and color taste good, at the end of treatment is widely used in industrial organic waste gas purification, good purifying effect. The gas pipeline into the absorption tower, in the two generation diffusion process between different diffusion end gas is sucked out and the fan discharge.
蓝阳环保，咨询热线：0519-81668662，13179310883，欢迎您的来电垂询！~~
一、工作原理
酸雾废气由风管引入净化塔，经过填料层，废气与氢氧化钠吸收液进行气液两相充分接触吸收中和反应，酸雾废气经过净化后，再经除雾板脱水除雾后由风机排入大气。吸收液在塔底经水泵增压后在塔顶喷淋而下，最后回流至塔底循环使用。净化后的酸雾废气达到广东省地方排放标准的排放要求，低于国家排放标准。
二、特点
1.除尘脱硫效率高，采用碱性洗涤水时，脱硫效率可达85%；
2.设备占地少，安装方便；
3.耗水、耗电指标较低；
4.耐腐蚀、不磨损，使用寿命长；
5.设备运行可靠，维护简单、方便。
三、结构
喷淋塔内填料层作为气液两相间接触构件的传质设备。喷淋塔底部装有填料支承板，填料以乱堆方式放置在支承板上。填料的上方安装填料压板，以防被上升气流吹动。喷淋塔喷淋液从塔顶经液体分布器喷淋到填料上，并沿填料表面流下。气体从塔底送入，经气体分布装置分布后，与液体呈逆流连续通过填料层的空隙，在填料表面上，气液两相密切接触进行传质。当液体沿填料层向下流动时，有时会出现壁流现象，壁流效应造成气液两相在填料层中分布不均，从而使传质效率下降。因此，喷淋塔内的填料层分为两段，中间设置再分布装置，经重新分布后喷淋到下层填料上。
活性炭吸附装置（PP材质）
产品名称：活性炭吸附装置（PP材质）
产品型号：SYD-HXT
产品简介：
活性炭吸附塔，是一种高效率经济实用型有机废气的净化与治理装置；是一种废气过滤吸附异味的环保设备产品。
产品详情
活性炭吸附装置（PP材质）
活性炭吸附塔能对苯、醇、酮、觯、酯、汽油类等有机溶剂的废气吸附回收，更适用于小风量高浓度的废气治理，因此喷涂、食品加工、印刷电路板、半导体制造、化工、电子、制皮业、乳胶制品业、 造纸等行业均可选用. 活性炭吸附设备主要是利用多孔性固体吸附剂活性炭具有吸附作用，能有效的阹除工业废气中的有机类污染物质和色味等，广泛应用于工业有机废气净化的末端处理，净化效果良好。气体经管道进入吸收塔后，在两个不同相界面之间产生扩散过程，扩散结束，气体被风机吸出并排放出去.
Organic waste gas purification tower, organic waste gas treatment tower, painting waste gas purification tower, hydrochloric acid waste gas purification tower processing custom
First, the working principle
The introduction of acid mist exhaust purification tower by air duct, exhaust gas passes through the filler layer, and sodium hydroxide absorption liquid two-phase full contact absorption neutralization reaction, acid mist emissions after cleaning, the demisting plate dehydration fog by the fan into the atmosphere. The absorption liquid is sprayed at the top of the tower by a water pump, and then is sprayed down to the bottom of the tower. Acid mist emissions after purification reached Guangdong local discharge standard requirements, lower than the national emission standard.
Two, characteristics
1 the efficiency of dust removal and desulfurization is high, the desulfurization efficiency can reach to 85% when using alkaline washing water;
2 equipment area is small, easy to install;
3 water consumption, low power consumption indicators;
4 corrosion resistance, no wear, long service life;
5 the equipment is reliable and easy to maintain.
Three, structure
The spray tower filler layer as a component of gas-liquid two phase contact mass transfer equipment. At the bottom of the spray tower with packing support plate, packing to huddle place in the support plate. The filler is installed above the filler plate, in order to prevent rising air blowing. Spray tower spray liquid from the top of the tower by spraying liquid distributor to packing, and the packing surface along the flow. The gas is fed from the bottom of the tower, and is distributed with the liquid through the gas distribution device, and then flows through the gap of the packing layer. When the liquid flows along the packing layer, the wall flow phenomenon sometimes occurs, and the wall flow effect results in the uneven distribution of the gas-liquid two-phase in the packing layer, which leads to the decrease of the mass transfer efficiency. Therefore, the filler layer spray tower is divided into two sections, arranged in the middle of distribution device, the re distribution of spray to lower packing.
Activated carbon adsorption device (PP material)
Product Name: activated carbon adsorption device (PP material)
Item No: SYD-HXT
Product profile:
Activated carbon adsorption is an efficient purification tower, economical and practical organic waste and governance is a waste gas filtering device; adsorption odor environmental protection equipment products.
product details
Activated carbon adsorption device (PP material)
Activated carbon adsorption tower adsorption gas recovery of benzene, alcohol, ester, ketone, Zhi, gasoline and other organic solvent, is more suitable for small volume high concentration of exhaust gas, so spraying, food processing, printed circuit board, semiconductor manufacturing, chemical industry, electronics, leather, latex products industry, papermaking etc. the industry can be used. The activated carbon adsorption equipment is the use of porous solid adsorbent with activated carbon adsorption, in addition to Qu in industrial waste gas of organic pollutants and color taste good, at the end of treatment is widely used in industrial organic waste gas purification, good purifying effect. The gas pipeline into the absorption tower, in the two generation diffusion process between different diffusion end gas is sucked out and the fan discharge.
相关产品推荐
-
湖州废气处理_湖州工业废气处理_湖州活性炭吸附塔 厂家定制
-
南京废气处理,徐州废气处理,苏州废气处理 加工定制
-
印刷厂废气处理-制药厂废气处理-喷涂厂废气处理-化工厂废气处理-喷漆厂废气处理
-
UV光解氧化设备/UV光解废气处理/uv光解除臭设备/uv光催化氧化设备 供应厂家
-
有机废气净化、废气净化设备、废气净化工程、废气净化装置 环保达标
-
电子厂废气处理-鱼粉厂废气处理-电镀厂废气处理-皮革厂废气处理 厂家生产
-
农药厂废气处理\橡胶厂废气处理\家具厂废气处理\污水厂废气处理\冶炼厂废气处理
-
玻璃钢净化塔\玻璃钢酸雾塔\玻璃钢废气塔\玻璃钢填料塔\玻璃钢废气吸收塔
-
活性炭吸附装置-活性炭吸附设备-填料塔-玻璃钢废气处理塔-专业厂家
-
专注于聚丙烯废气吸收塔-吸附塔-不锈钢废气塔-不锈钢废气处理塔