厂商 :灵石岢岚即墨有限公司
西藏 林芝- 主营产品:
焊接连接阀门办证评审细则;快办湖北鄂州换无缝钢管高压锅炉管证流程 |
管子的壁厚契合计划文件的需求,因而本次修订添加了“且不得小于计划文件规则的最小壁厚”。 6.1.8 Defect may occur during the pipe bending, therefore, in order to ensure the wall thickness after grinding the defect can reach the design thickness, this revision has supplemented that “and shall not less be than the minimal wall thickness given in the design document”. 6.1.10 本条规则了夹套管预制进程中施工单位应履行的要害技能需求,若计划有更具体的规则,应履行计划文件的规则。 6.1.10 This clause specifies the critical technical requirements to be followed by the construction unit during the prefabrication of ja
cket pipe.
If more detailed requirement is provided in the design document, this design
document shall be complied with. 6.1.11 管道内部清洁,是施工质量好坏的重要标志,是投料试车一次成功的要害条件之一,本规范6.2.1条也有管道内部清洁的需求。多年来,因为管道内部不洁净,严重影响试车进程,影响商品质量,有着深入的经验。所以预制合格的管道,一定要确保内部清洁,并及时关闭其端口。 6.1.11 The internal cleanness of the piping is the essential aspect
affecting the construction quality, the critical requisition for the successful
commissioning and service at the first time. Clause 6.2.1 of this specification
also specifies the internal cleanness of piping. Deepgoing lesson have been
learned from the serous impact to commissioning and production quality due to
uncleanness inside piping in the past years. Thus the inside of qualified
prefabricated pipes shall be kept clean and the end openings shall be timely
closed. 6.2 管道设备 Piping Installation 6.2.9~6.2.11 这三条是管道与机器衔接时的需求。表6保存原规范SHJ 501-85表3.2.12的一切规则,GB 50235的规则见下表: 6.2.9~6.2.11 These three clauses are in regard to the requirements
on the connection of piping to machines. In Table 6, all the specification of
3.2.12 of Table SHJ 501-85 in the original specification has been maintained
and the following table lists the specification of GB 50235: 法兰平行度、同轴度答应偏差 Tolerance of flange parallelism depth and axiality 机器转速 Machine rotation speed r/min 平行度 Parallelism depth mm 同轴度 Axiality mm 3000~6000 ≤0.15 ≤0.50 >6000 ≤0.10 ≤0.20 相互对比,本规范保存了转速<3000 r/min时的需求,因为转速小于3000 r/min的滚动机器在石化职业里对比遍及。 Through the intercomparison, the requirement under the condition of
rotation speed of <3000r/min has been maintained in this specification as
the rotating machine with the rotation speed less than 300r/min is commonly
used in petrochemical industry. 管子与机器的法兰衔接处,单机试车前,应在联轴器上架表查看承认终究衔接情况,若有不合格,应进行调整,合格后方能进行试车。 The final connection status shall be checked for the flange c
! 以上内容是行业相关标准的节选,内容与标题没有直接的相关性,只是为了利于搜索引擎的收录。具体项目办理细节及流程欢迎您来电咨询,我们致力于把我们所擅长的项目做到最专业。
公司地址:南京市鼓楼区中央路417号先锋广场1033室
联系人:田雨 (业务经理)
手机号码:13770751414
联系电话:025-66639814
QQ:453472919
传真:025-66639971
Cl
-
代理液动阀阀门办常熟认证与代理办高压化肥无缝钢管生产许可证程序申办要
-
兴义精密内径无缝钢管办企业生产许可证和热轧无缝钢管拿江阴资质程序
-
止回阀阀门如何去办理办生产资质与去什么地方办液动阀门许可
-
UPVC管聚乙烯管怎么去办证流程.代办甘肃兰州拿石油裂化管无缝钢管认
-
办理泸州压力容器法兰办生产许可证程序与PE80聚乙烯管证评审细则马鞍
-
申办办地中亚锅炉用无缝钢管资质细则;黄州取中压阀阀门证流程
-
开断用阀门申办TS证要多少时间办.湖州去什么位置换金属阀体衬里阀门证
-
申办气瓶用无缝钢管办资质评审细则去哪里以及承插焊法兰申办要求办生产许
-
洪泽怎么样做办低温阀阀门证程序;毕节办精密内径无缝钢管资质流程申办
-
杭州非金属材料阀门办制造资质代理.ASTM-A106无缝钢管拿涪陵生