A10VSO18DRG/31R

A10VSO18DG A10VSO18DR A10VSO18DRG A10VSO18DFR A10VSO18DFR1 A10VSO18DFLR A10VSO18DR/31R A10VSO18DFR/31R A10VSO18DFR1/31R A10VSO18DFLR/31R A10VSO18DG/31R A10VSO18DRG/31R A10VSO28DG A10VSO28DR A10VSO28DRG A10VSO28DFR A10VSO28DFR1 A10VSO28DFLR A10VSO28DG/31R A10VSO28DR/31R A10VSO28DRG/31R A10VSO28DFR/31R A10VSO28DFR1/31R A10VSO28DFLR/31R A10VSO45DG A10VSO45DR A10VSO45DRG A10VSO45DFR A10VSO45DFR1 A10VSO45DFLR A10VSO45DG/31R A10VSO45DR/31R A10VSO45DRG/31R A10VSO45DFR/31R A10VSO45DFR1/31R A10VSO45DFLR/31R A10VSO71DG A10VSO71DR A10VSO71DRG A10VSO71DFR A10VSO71DFR1 A10VSO71DFLR A10VSO71DG/31R A10VSO71DR/31R A10VSO71DRG/31R A10VSO71DFR/31R A10VSO71DFR1/31R A10VSO71DFLR/31R A10VSO100DG A10VSO100DR A10VSO100DRG A10VSO100DFR A10VSO100DFR1 A10VSO100DFLR A10VSO100DG/31R A10VSO100DR/31R A10VSO100DRG/31R A10VSO100DFR/31R A10VSO100DFR1/31R A10VSO100DFLR/31R A10VSO140DG A10VSO140DR A10VSO140DRG A10VSO140DFR A10VSO140DFR1 A10VSO140DFLR A10VSO140DG/31R A10VSO140DR/31R A10VSO140DRG/31R A10VSO140DFR/31R A10VSO140DFR1/31R A10VSO140DFLR/31R A10VSO18DG/31R-PPA12N00 A10VSO18DR/31R-PPA12N00 A10VSO18DRG/31R-PPA12N00 A10VSO18DFR/31R-PPA12N00 A10VSO18DFR1/31R-PPA12N00 A10VSO18DFLR/31R-PPA12N00 A10VSO28DG/31R-PPA12N00 A10VSO28DR/31R-PPA12N00 A10VSO28DRG/31R-PPA12N00 A10VSO28DFR/31R-PPA12N00 A10VSO28DFR1/31R-PPA12N00 A10VSO28DFLR/31R-PPA12N00 A10VSO45DG/31R-PPA12N00 A10VSO45DR/31R-PPA12N00 A10VSO45DRG/31R-PPA12N00 A10VSO45DFR/31R-PPA12N00 A10VSO45DFR1/31R-PPA12N00 A10VSO45DFLR/31R-PPA12N00 A10VSO71DG/31R-PPA12N00 A10VSO71DR/31R-PPA12N00 A10VSO71DRG/31R-PPA12N00 A10VSO71DFR/31R-PPA12N00 A10VSO71DFR1/31R-PPA12N00 A10VSO71DFLR/31R-PPA12N00 A10VSO100DG/31R-PPA12N00 A10VSO100DR/31R-PPA12N00 A10VSO100DRG/31R-PPA12N00 A10VSO100DFR/31R-PPA12N00 A10VSO100DFR1/31R-PPA12N00 A10VSO100DFLR/31R-PPA12N00 A10VSO140DG/31R-PPB12N00 A10VSO140DR/31R-PPB12N00 A10VSO140DRG/31R-PPB12N00 A10VSO140DFR/31R-PPB12N00 A10VSO140DFR1/31R-PPB12N00 A10VSO140DFLR/31R-PPB12N00 　　4、叶片在转子槽内被卡住，根本抛不出来，或者叶片折断，叶片折断造成高、低压腔形成互通。叶片与槽配合过紧应为滑动配合，其配合间隙为0.0150.02m，并应去毛刺。 　　 　　5、配油盘缺损及配油盘与泵体接触不良，造成密封区域被沟通，配油盖侧面有微小变形，修整配油盘与转子的接触面。 　　 　　6、电机反转:将电机反向旋转。 　　 　　7、油液粘度过大:改用适当粘度的油液。 　　 　　8、未装连接器或花键轴不转或花键轴扭断等:装上连接键，更换花键轴。 　　 　　9、吸油管过长:使泵靠近油箱，即相应缩短了进油管的长度。 　　 　　10、泵体质里(砂眼、气孔等):调换新泵体。