厂商 :深圳美氏康宁胶业
广东 深圳- 主营产品:
- 酸性胶
- 耐候胶
- 结构胶
联系电话 :13926500079
商品详细描述
优质环保玻璃胶密封胶“美氏M6478”中性硅酮密封胶是一种中性固化的高性能密封胶:
1)不腐蚀基材;
2)固化收缩率低;
3)在低温(-45℃)至高温(+164℃)内保持弹性;
4)柔软抗震,耐变形;
5)适合于玻璃,铝材,石材,混凝土,砖瓦,陶瓷,塑料间的非结构性粘结密封:
6)在铅、镉等六项有害物质的含量上达到了ROHS指令的要求,可以在欧盟范围内进行销售。
说明:
1)施工温度在5℃~40℃之间;
2)用两块布法清洁基材;
3)将胶嘴按需要的大小做45°切断;
4)将胶打满接缝处。
重要:
1)使用前请做材料相容性测试;
2)不用于结构性装配或表面温度(45℃)以上的材料;
3)不用于渗出油污或溶剂的材料。
注意:
远离儿童!
避免接触眼睛和皮肤!
如有接触,请用水冲洗;仍然不适的请就医检查。
执行标准:GB/T14683-2003
保质期:9个月(<24℃).
“MEISHI M6478”neutral silicone sealant is a neutral cure high perfomance grade silicone sealant:
1)Not corrosion to the materials;
2)Low shrinkage on curing;
3)Keep elastic in low(-45℃) and high(+164℃) temperatures;
4)High grade soft,be able to bear oscillation;
5)Suitable for glass,aluminum material,stone,concrete, brick, ceramic, plastic, non-structural bonding and sealing;
6)In the lead, cadmium and other hazardous substances six reached the ROHS directive, can be sold within the EU
DIRECTIONS:
1)Construcation applycable between 5℃~40℃;
2)Substrates should be solvent cleaned using two clothes method;
3)Cut the nozzle to desired opening at 45°angle;
4)Fill the joint completely.
1)不腐蚀基材;
2)固化收缩率低;
3)在低温(-45℃)至高温(+164℃)内保持弹性;
4)柔软抗震,耐变形;
5)适合于玻璃,铝材,石材,混凝土,砖瓦,陶瓷,塑料间的非结构性粘结密封:
6)在铅、镉等六项有害物质的含量上达到了ROHS指令的要求,可以在欧盟范围内进行销售。
说明:
1)施工温度在5℃~40℃之间;
2)用两块布法清洁基材;
3)将胶嘴按需要的大小做45°切断;
4)将胶打满接缝处。
重要:
1)使用前请做材料相容性测试;
2)不用于结构性装配或表面温度(45℃)以上的材料;
3)不用于渗出油污或溶剂的材料。
注意:
远离儿童!
避免接触眼睛和皮肤!
如有接触,请用水冲洗;仍然不适的请就医检查。
执行标准:GB/T14683-2003
保质期:9个月(<24℃).
“MEISHI M6478”neutral silicone sealant is a neutral cure high perfomance grade silicone sealant:
1)Not corrosion to the materials;
2)Low shrinkage on curing;
3)Keep elastic in low(-45℃) and high(+164℃) temperatures;
4)High grade soft,be able to bear oscillation;
5)Suitable for glass,aluminum material,stone,concrete, brick, ceramic, plastic, non-structural bonding and sealing;
6)In the lead, cadmium and other hazardous substances six reached the ROHS directive, can be sold within the EU
DIRECTIONS:
1)Construcation applycable between 5℃~40℃;
2)Substrates should be solvent cleaned using two clothes method;
3)Cut the nozzle to desired opening at 45°angle;
4)Fill the joint completely.
相关产品推荐