厂商 ：山东临朐铁力士破碎设备有限公司
山东 潍坊- 主营产品：
联系电话 ：18663616727
商品详细描述
概述
辊压机是我公司在引进、吸收德国辊压机先进技术的基础上，结合洪堡和伯力鸠斯辊机的优点，研制开发的最可靠的固体物料粉磨设备，适用于抗压强度小于300mpa，湿度小于30%的硬物料的细碎和中碎作业，可广泛用水泥、矿山、冶金、陶瓷等行业。
辊压机配置两个实心碾辊，辊面采用堆焊辊面，适用于进料粒度小于1400mm，成品粒度要求4-15mm以下的中细碎作业。如水泥行业磨机前的预破水泥熟料、石灰石及复合材料；铁矿行业入磨前预碎钢渣、铁矿石、硅矿石；免烧砖厂破碎各种矿石做免烧砖等；或者与上述类似的破碎场合。
Summarize
On the basis of advanced technolgy fromGermany , we developed this most reliable solid material grinding equipent-rolling press which has the advantages of both Humboldt and Khabarovsk
Rolling press has two solid abrasive rolls of overlay welding surface. It is for the intermediate and fine crushing, maxium feeding 140mm,maxium discharge 4-15mm. Such as befoue the mill: cement industry pre-crushing cement clinker, limestone and composite materials; iron ore industry pre-crushing slag, iron ore, silica minerals;brick factory pre-crushing kinds of ore to produce unburned brick; or in the similar occasions.
2PGY Series Rolling press
工作原理
辊压机的主体是依靠两个相向转动的实心碾辊，物料通过辊压机的布料装置，进入两个大小相同，相对转动的辊隙（V型破碎腔），采用高压料层粉碎原理，物料经过高压挤压（一般压力设置150Mpa），彻底破坏了物料的内部晶体结构，使物料产生大量微裂纹，使物料机理发生改变，从而达到密实的物料饼和粉料，最后从两辊隙中落下，经出料口由输送设备送出。
Working principal
The main body of rolling press is two solid abrasive rolls that are relatively rotating.Through the arrangement equipment, the material enters into two relatively rotating, equal size roll gaps. Principle of using high pressuer grinding materiao layer, through the high pressure extrusion(typically pressrue is set to 150Mpa), the internal crystal structure of materials is completely destroyed, create q large number of micro-cracks, change the mechanism of materials achieve the dense material cake and powder, and finally fall from the gap bwteen the rolls, sent by the transport equipment.
主要技术参数/Specifications
辊压机是我公司在引进、吸收德国辊压机先进技术的基础上，结合洪堡和伯力鸠斯辊机的优点，研制开发的最可靠的固体物料粉磨设备，适用于抗压强度小于300mpa，湿度小于30%的硬物料的细碎和中碎作业，可广泛用水泥、矿山、冶金、陶瓷等行业。
辊压机配置两个实心碾辊，辊面采用堆焊辊面，适用于进料粒度小于1400mm，成品粒度要求4-15mm以下的中细碎作业。如水泥行业磨机前的预破水泥熟料、石灰石及复合材料；铁矿行业入磨前预碎钢渣、铁矿石、硅矿石；免烧砖厂破碎各种矿石做免烧砖等；或者与上述类似的破碎场合。
Summarize
On the basis of advanced technolgy from
Rolling press has two solid abrasive rolls of overlay welding surface. It is for the intermediate and fine crushing, maxium feeding 140mm,maxium discharge 4-15mm. Such as befoue the mill: cement industry pre-crushing cement clinker, limestone and composite materials; iron ore industry pre-crushing slag, iron ore, silica minerals;brick factory pre-crushing kinds of ore to produce unburned brick; or in the similar occasions.
2PGY Series Rolling press
工作原理
辊压机的主体是依靠两个相向转动的实心碾辊，物料通过辊压机的布料装置，进入两个大小相同，相对转动的辊隙（V型破碎腔），采用高压料层粉碎原理，物料经过高压挤压（一般压力设置150Mpa），彻底破坏了物料的内部晶体结构，使物料产生大量微裂纹，使物料机理发生改变，从而达到密实的物料饼和粉料，最后从两辊隙中落下，经出料口由输送设备送出。
Working principal
The main body of rolling press is two solid abrasive rolls that are relatively rotating.Through the arrangement equipment, the material enters into two relatively rotating, equal size roll gaps. Principle of using high pressuer grinding materiao layer, through the high pressure extrusion(typically pressrue is set to 150Mpa), the internal crystal structure of materials is completely destroyed, create q large number of micro-cracks, change the mechanism of materials achieve the dense material cake and powder, and finally fall from the gap bwteen the rolls, sent by the transport equipment.
主要技术参数/Specifications
|
序号 Serial number |
规格型号 Model |
碾辊直径 （mm） Roll diameter |
碾辊宽度 （mm） Roll width |
进料粒度 (mm) Feed size |
出料粒度 （mm） Discharge size |
生产能力 （t/h） Output |
电机功率 （kw） Power |
保护方式 Protection mode |
|
1 |
2PGY1206 |
1200 |
600 |
＜80 |
＜4 |
120-180 |
185×2 |
液压 Hydraulic pressure |
|
2 |
2PGY1208 |
1200 |
800 |
＜80 |
＜4 |
150-240 |
200×2 | |
|
3 |
2PGY1406 |
1400 |
600 |
＜100 |
＜4 |
240-295 |
250×2 | |
|
4 |
2PGY1409 |
1400 |
900 |
＜100 |
＜4 |
290-360 |
280×2 | |
|
5 |
2PGY1609 |
1600 |
900 |
＜120 |
＜4 |
340-500 |
325×2 | |
|
6 |
2PGY1612 |
1600 |
1200 |
＜120 |
＜4 |
400-610 |
355×2 | |
|
7 |
2PGY1812 |
1800 |
1200 |
＜140 |
＜4 |
620-750 |
500×2 |
标签：
相关产品推荐
