HDMI延长器50m/164ft

HDMI延长器 在单50m/164ftUTP电缆与 双红外控制

 HDMI Extender

over single50m/164ftUTP Cables with

 

Dual IR Control

 User manual

Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.

INTRODUCTION

The HDMI Extender over Single Cat5e/6 with Bi-directional IR extends high definition video and audio signals and IR, at a distance of up to164ft/50mover a single Cat5e/6 cable.  Features EDID management,  which allows and encourages source and display “handshake” for seamless integration.  With only one cost effective Cat5e/6 cable, high definition sources with HDMI outputs can be connected to high definition displays with HDMI inputs over long distances.  Deep color video, DTS-HD or Dolby TrueHD audio is supported and compatible with the extender.  In addition, the extender is also equipped with bi-directional IR pass-through which allows for source or display control.

The extender includes two units: transmitting unit  and receiving unit.  The transmitting unit is used to capture the HDMI input with IR signals and carries the signals via one cost effective Cat5e/6 cable.  The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR and serial control signals.  The extender offers the most convenient solution for HDMI extension over a single Cat5e/6 with long distance capability, and is the perfect solution for any application.

FEATURES

Allows HDMI Audio/Video and IR signals to be transmitted over a single Cat5e/6 cable

Bi-directional IR system allowing for control of source or display (IR accessories included)

2D/3D  EDID management

TransmissionRange: Extends 1080p resolution up to164ft/50mover a single Cat5e or Cat6 cable

Works with HDMI and HDCP compliant devices

Supports up to 1080p High Definition resolution

Compact design for an easy and flexible installation

SPECIFICATIONS

Video Bandwidth:  Single-link 165Mhz [ 4.95Gbps]

Video Support:  480i/480p/720p/1080i/1080p @60

Audio Support:  Surround Sound (up to 7.1 ch) or stereo digital audio

TransmissionRange:  HD [1080p 24-bit color] – up to50m[164ft]

Input TMDS Signal:  3.3 volts

Input DDC Signal:  5.0 volts/P-P

ESD Protection:  Human Body model:         +/- 8 kV (air-gap discharge)

+/- 4 kV (contact discharge)

PCB stack-up:  4 layouts

HDMI connector:  Type A 19 pin female

RJ-45 connector:  WE/SS 8P8C 

3.5mmconnector:  (TX and RX) IR Receiver/IR Blaster

MECHANICAL SPECS

Housing:  Metal enclosure

Power Supply:  (2) 5V1ADC

Power consumption:  2.5 watts (TX); 1.2 watts (RX)

Operation temperature:  32~104 °F

Storage temperature:  -4 ~140 °F

Relative humidity:  20~90 % RH (no condensation)

Package Contents: 

HDMI Transmitter --------------------------------------------1pcs

HDMI Receiver------------------------------------------------1pcs

Windband IR Tx cable --------------------------------------- 1pcs

windband IR Rx cable  --------------------------------------- 1pcs

5V1ADC Power Supply Adaptor ------------------------- 2 Pcs

Product Manual -----------------------------------------------1pcs

 

PANEL DESCRIPTIONS

Transmitting unit

 = 1 \* Arabic 1. Power LED: This LED will illuminate when the device is connected with power supply.

2. HDMI IN: This slot is where you connect the HDMI output port of your source equipment such as DVD/Blu-ray players or Set-Top-Box with an HDMI cable.

3. DC 5V: Connect from 5V DC power supply into the unit and connect the adaptor to an AC outlet.

4. EDID:  The switcher can switch 2D or 3D EDID information to DVD.

5. CAT6:Connect the CAT output of the transmitter with the CAT input of the receiver with CAT5E/6 cable.

6. IR TX: Connect the IR Blaster cable included in the package for IR signal transmission. Pace the IR blaster in direct line-of-sight of the equipment to be controlled.

7. IR RX: Connect to the IR Receiver for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR receiver.

Receiver unit 

1. LOCK LED: This LED will illuminate when the HDMI signal  from the transmitter is stable.

2. HDMI OUT: This slot is to connect the HDMI input port of your display such as an HDTV.

3. DC 5V: Connect from 5V DC power supply into the unit and connect the adaptor to an AC outlet.

4. EQ: HDMI Receiver equalizer switcher,LOW for 0—20mCAT5E/6 calbe,High for 20-50mCAT5E/6 calbe.

5. CAT6:Connect the CAT input of the receiver with the CAT output of the transmitter with CAT5E/6 cable.

6. IR RX: Connect to the IR Receiver for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR receiver.

7. IR TX: Connect the IR Blaster cable included in the package for IR signal transmission. Pace the IR blaster in direct line-of-sight of the equipment to be controlled.

CONNECTION DIAGRAM CONNECT AND OPERATE

1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit.

2. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit.

3. Connect a single Category 5e/6 up to164ft/50mto the output of the Transmitting unit, and the other end to the input of the Receiving unit.

4. For power, plug both the Transmitting unit and Receiving unit with the included power supplies.

5. Power on each device in the same sequence (receiver and transmitter will already be powered when either unit is plugged in.)

At this point the display connected should display the source signal connected to the extender set. If no signal is being displayed, check the receiver EQ swithcer(LOW for 0-20mcat6 cable ,HIGH for 20-50mcat6 cable).  If a display is having difficulty receiving a signal, see EDID section and perform EDID learning or access the display’s menu and adjust the resolution (lowest to highest until signal is displayed). A 24 Hz vertical refresh rate may work better than 60 Hz or higher. Use the source remote at the receiver emitter to test IR functionality.  If the IR remote function is not responding, check the emitters to ensure they are placed correctly and are plugged into the correct IR jacks on the Extender set receiving and transmitting units.

Wideband IR(20KHz---60KHz) introduction

IR BLASTER (TX)

To control the source:  Plug IR Blaster intoIRTXport of transmitter unit; place blaster in front of the IR eye of the source.

To control the display:  Plug IR Blaster intoIRTXport of receiver unit; place blaster in front of the IR eye of the display.

IR RECEIVER (RX)

To control the source:  Plug IR Receiver into IR RX port of receiver unit; place receiver at or near display.

To control the display:  Plug IR Receiver into IR RX port of transmitter unit; place receiver in position where it is able to receive remote signals.

联 系 人：李坤华

电话：0755-26978292

手机:13926523252 /15012968821

      QQ：2457601443/2518185488

    旺旺：时代次方科技

公司邮箱：sales8@otime.biz

公司网址：http://www.otime.biz/

阿里巴巴：http://otime9.1688.com/