厂商 ：深圳市腾达兴科技有限公司
广东 深圳- 主营产品：
- 防盗器充电器
- 电源适配器
- 机顶盒电源
联系电话 ：13410276585
商品详细描述
详细信息
1、描述/DESCRIPTION:
本规格书适应于9VDC20000mA 型号的开关电源。
The purpose of the document is to specify the functional requirements of a 18W switching power supply.
2、输入特性/INPUT CHARACTERISTICS:
2.1输入电压/Input Voltage:
额定电压/Rated Voltage:100~240Vac
调整范围/Variation Range:90-264Vac
2.2输入频率/Input Frequency:
额定频率/Rated Frequency:50/60Hz
调整频率/Variation Frequency:47-63Hz
2.3输入电流/Input Current:
当输入交流电压为额定值的下限电压负载满载时，最大输入交流电流3A.
3 Amps max At any input voltage and rated,DC output rated load.
2.4浪涌电流/Inrush Current:
当输出为额定负载，环境温度为25℃，输入240Vac 冷态起机时的最大浪涌电流小于60A。
120 Amps Max. Cold start at 240Vac input,with rated load and 25℃ ambient.
2.5AC漏电流/AC Leakage Current:
当输入电压240Vac时，最大漏电流为10mA。
10mA Max.At240Vac input.
3、输出特性/OUTPUT CHARACTERISTICS:
3.1输出功率/Power output
3.2负载特性，调整率/Combined Load/Line Regulation
3.3波纹和噪声 Ripple and Noise:
测试条件：在额定电压及额定负载条件下，使用示波器带宽为20MHz连接到充电器的输出端，同时输出端并联一个47uF的电解电容和一个0.1uF的瓷片电容。
Under nominal voltage and nominal load,the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and parallel 47uF/0.1uF,crossed connected at testing point.
电压 最大波纹/最大噪声
Voltage Ripple and Noise(Max)
+9Vdc 150m V p-p
3.4上升时间/Rise time:
当输入220Vac和输出最大负载时最大时间为40mS。
40 mS Max. At 220Vac input and output MAX load.
3.5保持时间/Hold up time.
当输入220Vav和输出最大负载时最大时间为40mS.
40 mSMin.at 220Vac input and output Max.Load.
3.6效率/Efficiency:
当230Vac输入电压时,，1/4，1/2，3/4和满载计算平均效率，最小60%。
60% Min.At 115/230Vac input voltage,1/4,1/2,3/4and full load calculation average efficiency.
保护功能/PROTECTION FUNCTION:
短路测试/Short circuit test:
该电源供给器在短路解除时能正常工作恢复。
The power supply mill be auto recovered when short circuit faults remove.
5、环境要求/ENVIRONMENTAL REQUIRENET:
5.1工作温度/Operating Temperature:
0℃-40℃，满载，正常工作.
0℃ to 40℃,Full load,Normal operation.
5.2储藏温度/Storage Temperature:-20℃ to 80℃
带外壳/With package
5.3工作湿度/Relative Humidity:
5%(0℃)~90%(40℃)，72小时，满载，正常工作。
5%(0℃)~90%(40℃)RH，72Hrs,Full load,Normal operating.
5.4振动/Vibration
1.测试标准：国际电工电子委员会
Operating:IEC 721-3-3 3M3
5~9Hz，A=1.5mm
加速度（9~200Hz，Acceleration 5m/S2）
2.运输/Transportation:
IEC 721-3-2 2M2
5-9Hz,A=3.5mm
9~200Hz,加速度 Acceleration=5m/S2
200~500Hz,加速度 Acceleration=15m/S2
3.轴向振动/Axes，10 cycles per axis.
在测试过程中不能出现永久性的损坏.
No permanent damage may occur during testing.
在电源开启和关闭后，样机能够恢复发哦最初条件.
The SAMPLE has to its original situation after power power off/on.
5.5跌落试验/Dropping packed:
插墙式跌落高度为0.8米、桌面式跌落高度为500mm；
1M for wallmount type and 760mm for desktop type as above described.
测试台面是厚13mm的夹木板，离地面高19-20mm
The horizontal surface consists of hardwood at least 13mm thick,mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor.
6、安全要求/SAFETY REQUIREMENT:
6.1.安全：符合标准CE(EN60950-1),AS/NZS:60950-1
Safety：accord with CE-(EN60950-1),AS/NZS:60950-1
6.2高压/DIELECTRIC STRENGTH Hi-pot：
初级对次级/Primary to secondary:1000 Vac 10mA/3S for type test.
6.3绝缘抗阻/Iusulation resistance:
初级对次级/Primary to secodary:10MΩ min at 500V DC.
6.4EMI 标准/EMI STANDARD
Meets the Limits of/测试符合
<1>.Fcc part 15 class B rules
<2>.EN55022 class B rules
<3>.GB9254-1998,GB17625.1-2003
本规格书适应于9VDC20000mA 型号的开关电源。
The purpose of the document is to specify the functional requirements of a 18W switching power supply.
2、输入特性/INPUT CHARACTERISTICS:
2.1输入电压/Input Voltage:
额定电压/Rated Voltage:100~240Vac
调整范围/Variation Range:90-264Vac
2.2输入频率/Input Frequency:
额定频率/Rated Frequency:50/60Hz
调整频率/Variation Frequency:47-63Hz
2.3输入电流/Input Current:
当输入交流电压为额定值的下限电压负载满载时，最大输入交流电流3A.
3 Amps max At any input voltage and rated,DC output rated load.
2.4浪涌电流/Inrush Current:
当输出为额定负载，环境温度为25℃，输入240Vac 冷态起机时的最大浪涌电流小于60A。
120 Amps Max. Cold start at 240Vac input,with rated load and 25℃ ambient.
2.5AC漏电流/AC Leakage Current:
当输入电压240Vac时，最大漏电流为10mA。
10mA Max.At240Vac input.
3、输出特性/OUTPUT CHARACTERISTICS:
3.1输出功率/Power output
|
电压 Voltage |
最小负载 Min.Load |
额定负载 Rated.Load |
待机功耗 Stand by power |
输出功率 Output power |
|
9Vdc |
0.01A |
2A |
1.2WMax |
18w |
3.2负载特性，调整率/Combined Load/Line Regulation
|
电压 Voltage |
最小负载 Min.Load |
额定负载 Rated.Load |
线性调整 Line Regulation |
负载调整 Load Regulation |
|
9Vdc |
0.01A |
2A |
±1% |
±5% |
3.3波纹和噪声 Ripple and Noise:
测试条件：在额定电压及额定负载条件下，使用示波器带宽为20MHz连接到充电器的输出端，同时输出端并联一个47uF的电解电容和一个0.1uF的瓷片电容。
Under nominal voltage and nominal load,the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and parallel 47uF/0.1uF,crossed connected at testing point.
电压 最大波纹/最大噪声
Voltage Ripple and Noise(Max)
+9Vdc 150m V p-p
3.4上升时间/Rise time:
当输入220Vac和输出最大负载时最大时间为40mS。
40 mS Max. At 220Vac input and output MAX load.
3.5保持时间/Hold up time.
当输入220Vav和输出最大负载时最大时间为40mS.
40 mSMin.at 220Vac input and output Max.Load.
3.6效率/Efficiency:
当230Vac输入电压时,，1/4，1/2，3/4和满载计算平均效率，最小60%。
60% Min.At 115/230Vac input voltage,1/4,1/2,3/4and full load calculation average efficiency.
保护功能/PROTECTION FUNCTION:
短路测试/Short circuit test:
该电源供给器在短路解除时能正常工作恢复。
The power supply mill be auto recovered when short circuit faults remove.
5、环境要求/ENVIRONMENTAL REQUIRENET:
5.1工作温度/Operating Temperature:
0℃-40℃，满载，正常工作.
0℃ to 40℃,Full load,Normal operation.
5.2储藏温度/Storage Temperature:-20℃ to 80℃
带外壳/With package
5.3工作湿度/Relative Humidity:
5%(0℃)~90%(40℃)，72小时，满载，正常工作。
5%(0℃)~90%(40℃)RH，72Hrs,Full load,Normal operating.
5.4振动/Vibration
1.测试标准：国际电工电子委员会
Operating:IEC 721-3-3 3M3
5~9Hz，A=1.5mm
加速度（9~200Hz，Acceleration 5m/S2）
2.运输/Transportation:
IEC 721-3-2 2M2
5-9Hz,A=3.5mm
9~200Hz,加速度 Acceleration=5m/S2
200~500Hz,加速度 Acceleration=15m/S2
3.轴向振动/Axes，10 cycles per axis.
在测试过程中不能出现永久性的损坏.
No permanent damage may occur during testing.
在电源开启和关闭后，样机能够恢复发哦最初条件.
The SAMPLE has to its original situation after power power off/on.
5.5跌落试验/Dropping packed:
插墙式跌落高度为0.8米、桌面式跌落高度为500mm；
1M for wallmount type and 760mm for desktop type as above described.
测试台面是厚13mm的夹木板，离地面高19-20mm
The horizontal surface consists of hardwood at least 13mm thick,mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor.
6、安全要求/SAFETY REQUIREMENT:
6.1.安全：符合标准CE(EN60950-1),AS/NZS:60950-1
Safety：accord with CE-(EN60950-1),AS/NZS:60950-1
6.2高压/DIELECTRIC STRENGTH Hi-pot：
初级对次级/Primary to secondary:1000 Vac 10mA/3S for type test.
6.3绝缘抗阻/Iusulation resistance:
初级对次级/Primary to secodary:10MΩ min at 500V DC.
6.4EMI 标准/EMI STANDARD
Meets the Limits of/测试符合
<1>.Fcc part 15 class B rules
<2>.EN55022 class B rules
<3>.GB9254-1998,GB17625.1-2003
相关产品推荐
