厂商 ：深圳市腾达兴科技有限公司
广东 深圳- 主营产品：
- 防盗器充电器
- 电源适配器
- 机顶盒电源
联系电话 ：13410276585
商品详细描述
12V1A电源适配器国标插墙式介绍：
1、描述/DESCRIPTION:
? 本规格书适应于12VDC1000mA型号的开关电源。
?? The purpose of the document is to specify the functional requirements of a 12W switching power supply.
2、输入特性/INPUT CHARACTERISTICS:
?? 2.1输入电压/Input Voltage:
????? 额定电压/Rated Voltage:100~240Vac
????? 调整范围/Variation Range:90-264Vac
?? 2.2输入频率/Input Frequency:
????? 额定频率/Rated Frequency:50/60Hz
????? 调整频率/Variation Frequency:47-63Hz
?? 2.3输入电流/Input Current:
????? 当输入交流电压为额定值的下限电压负载满载时，最大输入交流电流3A.
????? 3 Amps max At any input voltage and rated,DC output rated load.
?? 2.4浪涌电流/Inrush Current
????? 当输出为额定负载，环境温度为25℃，输入240Vac 冷态起机时的最大浪涌电流小于60A。
????? 120 Amps Max. Cold start at 240Vac input,with rated load and 25℃ ambient.
?? 2.5AC漏电流/AC Leakage Current:
????? 当输入电压240Vac时，最大漏电流为10mA。
????? 10mA Max.At240Vac input.
3. 输出特性/OUTPUT CHARACTERISTICS:
?? 3.1输出功率/Power output
??
?? 3.2负载特性，调整率/Combined Load/Line Regulation
??
?? 3.3波纹和噪声 Ripple and Noise:
?? 测试条件：在额定电压及额定负载条件下，使用示波器带宽为20MHz连接到充电器的输出端，同时输出端并联一个47uF的电解电容和一个0.1uF的瓷片电容。
?? Under nominal voltage and nominal load,the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and parallel 47uF/0.1uF,crossed connected at testing point.
?? 电压???????????????? 最大波纹/最大噪声
?? Voltage?????????????? Ripple and Noise(Max)
?? +12Vdc???????????????? 150m V p-p
?? 3.4上升时间/Rise time:
?? 当输入220Vac和输出最大负载时最大时间为40mS。
?? 40 mS Max. At 220Vac input and output MAX load.
?? 3.5保持时间/Hold up time.
?? 当输入220Vav和输出最大负载时最大时间为40mS.
?? 40 mSMin.at 220Vac input and output Max.Load.
?? 3.6效率/Efficiency:
?? 当230Vac输入电压时,，1/4，1/2，3/4和满载计算平均效率，最小60%。
?? 60% Min.At 115/230Vac input voltage,1/4,1/2,3/4and full load calculation average efficiency.
保护功能/PROTECTION FUNCTION:
????? 短路测试/Short circuit test:
????? 该电源供给器在短路解除时能正常工作恢复。
????? The power supply mill be auto recovered when short circuit faults remove.
5、 环境要求/ENVIRONMENTAL REQUIRENET:
?? 5.1工作温度/Operating Temperature:
????? 0℃-40℃，满载，正常工作.
????? 0℃ to 40℃,Full load,Normal operation.
?? 5.2储藏温度/Storage Temperature:-20℃ to 80℃
????? 带外壳/With package
?? 5.3工作湿度/Relative Humidity:
????? 5%(0℃)~90%(40℃)，72小时，满载，正常工作。
????? 5%(0℃)~90%(40℃)RH，72Hrs,Full load,Normal operating.
?? 5.4振动/Vibration
????? 1.测试标准：国际电工电子委员会
??????? Operating:IEC 721-3-3 3M3
??????? 5~9Hz，A=1.5mm
??????? 加速度（9~200Hz，Acceleration 5m/S2）
????? 2.运输/Transportation:
??????? IEC 721-3-2 2M2
??????? 5-9Hz,A=3.5mm
??????? 9~200Hz,加速度 Acceleration=5m/S2
??????? 200~500Hz,加速度 Acceleration=15m/S2
???? 3.轴向振动/Axes，10 cycles per axis.
?????? 在测试过程中不能出现永久性的损坏.
?????? No permanent damage may occur during testing.
?????? 在电源开启和关闭后，样机能够恢复发哦最初条件.
?????? The SAMPLE has to its original situation after power power off/on.
?? 5.5跌落试验/Dropping packed:
????? 插墙式跌落高度为0.8米、桌面式跌落高度为500mm；
????? 1M for wallmount type and 760mm for desktop type as above described.
????? 测试台面是厚13mm的夹木板，离地面高19-20mm
????? The horizontal surface consists of hardwood at least 13mm thick,mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor.
6、 安全要求/SAFETY REQUIREMENT:
?? 6.1.安全：符合标准CE(EN60950-1),AS/NZS:60950-1
????? Safety：accord with CE-(EN60950-1),AS/NZS:60950-1
?? 6.2高压/DIELECTRIC STRENGTH Hi-pot：
????? 初级对次级/Primary to secondary:1000 Vac 10mA/3S for type test.,
?? 6.3绝缘抗阻/Iusulation resistance:
????? 初级对次级/Primary to secodary:10MΩ min at 500V DC.
?? 6.4EMI 标准/EMI STANDARD
????? Meets the Limits of/测试符合
????? <1>.Fcc part 15 class B rules
????? <2>.EN55022 class B rules
????? <3>.GB9254-1998,GB17625.1-2003
1、描述/DESCRIPTION:
? 本规格书适应于12VDC1000mA型号的开关电源。
?? The purpose of the document is to specify the functional requirements of a 12W switching power supply.
2、输入特性/INPUT CHARACTERISTICS:
?? 2.1输入电压/Input Voltage:
????? 额定电压/Rated Voltage:100~240Vac
????? 调整范围/Variation Range:90-264Vac
?? 2.2输入频率/Input Frequency:
????? 额定频率/Rated Frequency:50/60Hz
????? 调整频率/Variation Frequency:47-63Hz
?? 2.3输入电流/Input Current:
????? 当输入交流电压为额定值的下限电压负载满载时，最大输入交流电流3A.
????? 3 Amps max At any input voltage and rated,DC output rated load.
?? 2.4浪涌电流/Inrush Current
????? 当输出为额定负载，环境温度为25℃，输入240Vac 冷态起机时的最大浪涌电流小于60A。
????? 120 Amps Max. Cold start at 240Vac input,with rated load and 25℃ ambient.
?? 2.5AC漏电流/AC Leakage Current:
????? 当输入电压240Vac时，最大漏电流为10mA。
????? 10mA Max.At240Vac input.
3. 输出特性/OUTPUT CHARACTERISTICS:
?? 3.1输出功率/Power output
??
?? 3.2负载特性，调整率/Combined Load/Line Regulation
??
?? 3.3波纹和噪声 Ripple and Noise:
?? 测试条件：在额定电压及额定负载条件下，使用示波器带宽为20MHz连接到充电器的输出端，同时输出端并联一个47uF的电解电容和一个0.1uF的瓷片电容。
?? Under nominal voltage and nominal load,the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and parallel 47uF/0.1uF,crossed connected at testing point.
?? 电压???????????????? 最大波纹/最大噪声
?? Voltage?????????????? Ripple and Noise(Max)
?? +12Vdc???????????????? 150m V p-p
?? 3.4上升时间/Rise time:
?? 当输入220Vac和输出最大负载时最大时间为40mS。
?? 40 mS Max. At 220Vac input and output MAX load.
?? 3.5保持时间/Hold up time.
?? 当输入220Vav和输出最大负载时最大时间为40mS.
?? 40 mSMin.at 220Vac input and output Max.Load.
?? 3.6效率/Efficiency:
?? 当230Vac输入电压时,，1/4，1/2，3/4和满载计算平均效率，最小60%。
?? 60% Min.At 115/230Vac input voltage,1/4,1/2,3/4and full load calculation average efficiency.
保护功能/PROTECTION FUNCTION:
????? 短路测试/Short circuit test:
????? 该电源供给器在短路解除时能正常工作恢复。
????? The power supply mill be auto recovered when short circuit faults remove.
5、 环境要求/ENVIRONMENTAL REQUIRENET:
?? 5.1工作温度/Operating Temperature:
????? 0℃-40℃，满载，正常工作.
????? 0℃ to 40℃,Full load,Normal operation.
?? 5.2储藏温度/Storage Temperature:-20℃ to 80℃
????? 带外壳/With package
?? 5.3工作湿度/Relative Humidity:
????? 5%(0℃)~90%(40℃)，72小时，满载，正常工作。
????? 5%(0℃)~90%(40℃)RH，72Hrs,Full load,Normal operating.
?? 5.4振动/Vibration
????? 1.测试标准：国际电工电子委员会
??????? Operating:IEC 721-3-3 3M3
??????? 5~9Hz，A=1.5mm
??????? 加速度（9~200Hz，Acceleration 5m/S2）
????? 2.运输/Transportation:
??????? IEC 721-3-2 2M2
??????? 5-9Hz,A=3.5mm
??????? 9~200Hz,加速度 Acceleration=5m/S2
??????? 200~500Hz,加速度 Acceleration=15m/S2
???? 3.轴向振动/Axes，10 cycles per axis.
?????? 在测试过程中不能出现永久性的损坏.
?????? No permanent damage may occur during testing.
?????? 在电源开启和关闭后，样机能够恢复发哦最初条件.
?????? The SAMPLE has to its original situation after power power off/on.
?? 5.5跌落试验/Dropping packed:
????? 插墙式跌落高度为0.8米、桌面式跌落高度为500mm；
????? 1M for wallmount type and 760mm for desktop type as above described.
????? 测试台面是厚13mm的夹木板，离地面高19-20mm
????? The horizontal surface consists of hardwood at least 13mm thick,mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor.
6、 安全要求/SAFETY REQUIREMENT:
?? 6.1.安全：符合标准CE(EN60950-1),AS/NZS:60950-1
????? Safety：accord with CE-(EN60950-1),AS/NZS:60950-1
?? 6.2高压/DIELECTRIC STRENGTH Hi-pot：
????? 初级对次级/Primary to secondary:1000 Vac 10mA/3S for type test.,
?? 6.3绝缘抗阻/Iusulation resistance:
????? 初级对次级/Primary to secodary:10MΩ min at 500V DC.
?? 6.4EMI 标准/EMI STANDARD
????? Meets the Limits of/测试符合
????? <1>.Fcc part 15 class B rules
????? <2>.EN55022 class B rules
????? <3>.GB9254-1998,GB17625.1-2003
相关产品推荐
