铝电解电容47UF/50V

厂商 :东莞市厦禾电子有限公司

广东 东莞
  • 主营产品:
  • 高压电容
  • 陶瓷电容
  • 碳膜电阻
联系电话 :15899916689
商品详细描述
NO.
ITEM 项目
TEST METHOD 测试方法
SPECIFICATION 规格
2.6
Surge test
突破试验
Rated surge voltage shall be applied (switch on )for 30±5 seconds and
 Then shall be applied (switch off)with discharge for 5±0.5 min at room
 temperature for 1000 cycles. Duration of one cycle is 6±0.5 minutes
在常温下施加(合上开关)额定涌浪电压30±5,然后停止施加(断开
开关)涌浪电压并且放电5±0.5分钟.这个循环工重复1000,6
±0.5分钟为一个循环周期.
Capacitance change:
Within ±20% of the initial
Specified value.
静电容量变化:
最初规定值的±20%以内.
Dissipation factor:
Less than 200% of the initial
Specified value.
损失角:低于最初规定值200%
Leakage current:
Within initial specified value.
泄漏电流:在最初规定值以内.
3.Mechanical characteristics 机械特性
NO.
ITEM 项目
TEST METHOD 测试方法
SPECIFICATION 规格
3.1
Lead strength
 端子强度
(A)    Tensile strength 拉伸强度:
Wire lead terminal 导针型:
Φd(mm)
0.45
0.5~0.8
0.8d1.25
Load(Kg)
0.51
1.0
2.0
Snap-in terminal 尖脚型:
Φd(mm)
Snap-in terminal 尖脚端子
Load (Kg)
2.0
The capacitor shall withstand the constant tensile force specified between the body and each lead for 10 seconds without damage either mechanical or electrical.
电容不得器各端子要承受规定的荷重10,不能有电气或机械特性上的损伤.
(B)    Bending strength 弯曲强度:
Wire lead terminal 导针型:
Φd(mm)
0.45
0.5~0.8
0.8d1.25
Load(Kg)
0.51
1.0
2.0
Snap-in terminal 尖脚型:
Cross section area of terminal
端子截面积(m)
Force
拉伸力(Kg)
0.5S1
1.0
S1
2.5
With the capacitor in a vertical position happily the load specified axially to each lead .The capacitor shall be rotated slowly from the vertical to the horizontal position, back to the vertical position. The 90°in the
opposite direction and back the original position. Performance of capacitor shall not have changed and leads shall be undated
给在竖直位置的电容器的每一端子以轴方向施加规定荷重,慢慢将电容器由竖直位置转至水平位置.然后向相反方向弯曲90°,再回到原来位置电容性能不能有变化及端子不能有损伤.
When the capacitance is
Measured, there shall be
No intermittent contacts,
or open-or short –circuiting.
测定静电容量时,不能有接
解不良,开路或短路.
 
 
 
 
There shall be no such
Mechanical damage as
Terminal damage etc.
不能有如端子受损之类的
机械特性上的损伤.
 
相关产品推荐