厂商 ：广州市速讯电子科技电子有限公司
广东 广州- 主营产品：
- 雕刻机
- 条幅机
- 广告设备
联系电话 ：13922239653
商品详细描述
产品简介
本产品为针对PVC、PE等可热熔性涂层膜材质平面的拼接而设计。
当喷绘画面超过喷绘机幅度时，就需要分次喷绘后再拼接，以及对喷绘画面的边缘进行增强处理、扦边、拉索、裹绳等，传统上是采用502及其衍生胶水等胶合剂的方式，这有很多不利之处，表现在：存在胶合速度慢、胶合强度不够、画面容易脏、工作效率低、难以掌握且操作繁琐、费工时，接驳宽幅大平面时需要比较大的工作场地。特别是一段时间后容易起泡起皱、导致表面不均匀，因为受空气温度的影响大，当在低温环境下胶合效果更不如意。
使用喷绘布无胶拼接机（简称热拼机），就能很好地解决以上诸多问题，免去使用胶合剂，且省工省时省事省场地，不论使用哪种布，灯箱布、枷网帆布等，不再受限制于高周波机器的平台长度，只要有一块相对平坦的耐热桌面或地面就可以随时作业，比如：长达百米的接缝可以一个人在50见方的空间完成作业。
本产品基于热风熔接技术，采用自走热压合原理，经过大量实践后不断改进，该机组装采用高扭力马达、精密减速机、耐热橡胶辊压轮，精加工不锈钢材料，高性能热风机，关键部位都采取二次增强处理，所以坚固耐用，且结构简单，结构都采取模块化组件，便于维护。
该机体积小、轻巧，净重仅15公斤、拥有可调自走接驳速度和恒温的特点，操作简单，仅取决于个人操作熟练和灵活程度。
一、应用范围
LC-3000智能型：适用于广告喷绘布行业，喷绘布、灯箱布、刀刮布、网格布等PVC、PE热熔性塑料膜材的焊接加工。
二、主要技术参数
额定电压： AC110-240V 频率： 50-60Hz
功率： 1000-3000W 温度调节范围： 0-500℃
调速范围： 1-15m/分钟 产品规格： 41*25*20cm
机身重量： 15-20Kg 拼接宽度： 2-5cm
三、特点
无胶拼接、温度速度可调，带有反馈温度传感器，可实时监测控制恒温（市场上一般为调压、温度随输入市电的电压变化而忽高忽低，不恒温）。无论拼接多长画面，拼接效果不会改变。增加了风量调节旋钮，更适合于拼接厚喷绘布。
四、操作步骤
1.首先把画面拉紧拉平，对好搭接缝（2-5cm）,用胶带或胶水固定在地面上。
2.接通电源，左转手柄，直至热风嘴与胶轮处于直线状态，再右转黑色旋钮，调节速度，一般把旋钮上的标记指向2的位置，设定完毕，右旋手柄直至热风嘴与地面脱离，行走即停。
3.设定温度。打开温度开关（右旋金色旋钮听到咔嚓声即可），按▲升温，按▼降温，根据布的薄厚和耐温性设定你需要的温度，一般情况在300-350℃之间，或者取些布材，对准风嘴，立即熔化即可，绝对不能出现烧焦现象，这时的温度也就是你所设定的温度。
4.温度和速度调试好后，把机器右轮的外沿与搭接缝的外沿靠齐放置等待实际温度与你设定的温度接近时，左旋手柄直至热风嘴完全嵌入到拼接缝里，机器就自动行走了，拼接开始。
5.在拼接过程中，若出现烧焦拼接物时，首先把速度提高一点点，或者把温度设定低（二者选一）即可避免熔坏拼接物了。但是绝对不能急速调节，否则机器速度过快，造成机器无法直行，给心理造成恐慌，或者无法粘接和损坏画面。
6.使用前，根据你的材质找准温度和速度的配合参数再使用。慢了会烧坏画面，快了会粘接不牢，所以温度和速度配合至关重要。
7.拼接完毕，右旋手柄，直至热风嘴完全脱离拼接物，随即关掉温度开关（即左旋金色旋钮，听到咔嚓声即可）。但绝对不可拔掉电源插头和关闭电源，以免余热损坏散热风机，造成损坏设备，无法使用。一定待机器实际温度降至最低时，才能拔掉电源插头和总开关。
8.严禁雨天使用，工作场地要干燥，平整，注意防火，设备要专人负责，专人操作，严禁不懂乱用。设备工作电压为：110V—240V(两种)严禁私自拆机，否则后果自负。
9. 保修期一年，加热件为易损品，不在保修范围内，但有责任为您提供配件，费用自理。
10. 随机配件：10m电源线一根，备用加热件一只，说明书及光盘一套。
11.产品若有改动，厂方不另行通知，请垂询当地经销商，产品说明仅供参考，不具备合同法律
效力，最终解释权归本厂所有。
12.本厂所有产品已申请国家多项专利，商标已注册，防造必究。
五、 维修与保养
维修设备需切断电源，并由专业技术人员检修。
Introduction
This product is for PVC, PE and other materials can be hot melt coated membrane plane designed for splicing.
When printing inkjet printers margins than the screen, you need to split after printing stitching, as well as printing are enhanced with the edge of the screen, Qian side, cable, wrapped in rope, etc., are traditionally used 502 and its derivatives glue and other adhesive means that there are many disadvantages, as follows: there is laminated slow, bonding strength is not enough, the screen easy to dirty, low efficiency, difficult to grasp and easy to operate, wasting time, when connected to large flat wide require larger workplaces. In particular, easy blistering after a period of wrinkles, resulting in uneven surface because the air temperature by the large, when the low temperature bonding effect is more unhappy.
Use no glue stitching cloth Welding Machine (referred to as Hot-air Welding Machine), can successfully resolve these many problems, remove the use of glue, save trouble and time were saved provincial venue, with either fabric, light box cloth, flails net canvas, etc., are no longer restricted to high-frequency machine platform length, as long as a relatively flat surface can heat your desktop or work at any time, for example: up to 100 meters of the joints can be a person in the space of 50 square homework .
This product is based on hot air welding technique, using principles of self-propelled hot together, after practice, after a large number of continuous improvement, high torque motor assembly machine, precision gear, heat resistant rubber rolling wheels, finishing stainless steel, high-performance hot air The key parts are taken by the second enhancement, so rugged and simple, modular structure components have been taken, and easy to maintain.
Machine is small, light, weight only 15 kg, with adjustable speed and constant self-propelled feeder features, simple operation, only depends on the individual operating proficiency and flexibility.
No glue splicing, temperature adjustable speed, with a feedback temperature sensor, real-time monitoring and control temperature (usually the market adjusted voltage, adjust the wind speed, temperature is not constant). No matter how long screen,welding screen effect will not change
Ⅰ、Field of application
LC-15 smart type: Suitable for advertising industry, inkjet fabric, inkjet fabric, light box cloth, Knife cloth, mesh cloth PVC, PE hot melt plastic membranes welding process.
Ⅱ、Main technical details
Rated voltage: AC110-240V Frequency: 50-60Hz
Power: 1000-3000W Temperature scope: 0-500℃
Speed scope: 1-15m/min Sepcification: 41*25*20cm
Weight: 15-20Kg Splicing width: 2-5cm
Ⅲ、Characterics
No glue splicing, temperature adjustable speed, with a feedback temperature sensor, real-time monitoring and control temperature (usually the market adjusted voltage, adjust the wind speed, temperature is not constant). No matter how long mosaic images,welding mosaic result will not change. With seting up a air flowing switch,it welds thick pvc easyily.
Ⅳ、Operation procedures
1、 First of all,lighten up the spraying cloth, target the sew.(2-5cm),and fix the cloth on the ground with glue or tape.
2、 Insert the power(picture),turn the handle to the left,till the spout is straight-line with the wheel.The turn the black button to the right ,adjust the speed, usually put it on 2.After adjust the speed,turn the handle to the right till the spout leave the ground.Then it stops.
3、 Adjust the temperature.Turn on the temperature button(turn the golden button to the right,it make the voice “Ka”.Then press the temperature up▲and down▼button,adjust the temperature according to the thickness and durable of the cloth,usually put it between300℃and350℃.Or you can put some materials in the spout,if the materials melt immediately and shouldn’t scorch.It is the proper temperature.
4、 After adjust the temperature and speed,put the edge of the right-wheel in a level with the edge of sew.When the actual temperature reach to your set temperature,turn the handle to the left till the spout insert into the sew totally.The machine beginstowalk.Splicing begins..
5、 During splicing,if the spout melt the spraying cloth. Fist you should turn black button to the right a little,or you can turn down the temperature.(choose one from the two ways) in that way,it won’t melt the cloth.But you shouldn’t turn the button in very urgent speed,or it will make the machine can’t weld or damage the cloth.
6、 Before using,please find a proper temperature and speed.If slow,it will damage the cloth;if fast,it may stick not so fasten,so it is important to adjust the temperature and speed.
7、 On the completion of splicing ,turn the handle to the right ,till the spout leave the spraying cloth totally.At this time,you can turn off the temperature button.But you couldn’t turn off the power cord and the power button, in case the heat damage the heat gun,and make the machine couldn’t work.You must wait till its actural temperature reach to the lowest.
8、 Don’t use the machine in wet weather.The working place must be dry and flat.Pay attention to the fire, the machine should have technical person to operate. The working voltage is 110V-240V(two types) To open the machine,you should be responsible for the result yourself.
9、 The warranty period is six months,heating elements are not in the warranty scope due to it being a repid-wear article,and we are only responsible for the supply of fitting,but the cost is subject to the client.
10、 Fitting equipped along with the machine include a source line of 10m,a piece of alternate heating element,a instrution book and a CD.
11、 we won’t notify if the products have some change.Please tell the agents in local area, the introduction is only for reference,don’t have legal effect.The factory has the final interpretation.
12、 All the products of this factory have applied the national patents.And the trademark has been registered,no copy allowed.
Errors and methods to solve
Repairing the machine with power is forbidden,it should by teachnical person.
本产品为针对PVC、PE等可热熔性涂层膜材质平面的拼接而设计。
当喷绘画面超过喷绘机幅度时，就需要分次喷绘后再拼接，以及对喷绘画面的边缘进行增强处理、扦边、拉索、裹绳等，传统上是采用502及其衍生胶水等胶合剂的方式，这有很多不利之处，表现在：存在胶合速度慢、胶合强度不够、画面容易脏、工作效率低、难以掌握且操作繁琐、费工时，接驳宽幅大平面时需要比较大的工作场地。特别是一段时间后容易起泡起皱、导致表面不均匀，因为受空气温度的影响大，当在低温环境下胶合效果更不如意。
使用喷绘布无胶拼接机（简称热拼机），就能很好地解决以上诸多问题，免去使用胶合剂，且省工省时省事省场地，不论使用哪种布，灯箱布、枷网帆布等，不再受限制于高周波机器的平台长度，只要有一块相对平坦的耐热桌面或地面就可以随时作业，比如：长达百米的接缝可以一个人在50见方的空间完成作业。
本产品基于热风熔接技术，采用自走热压合原理，经过大量实践后不断改进，该机组装采用高扭力马达、精密减速机、耐热橡胶辊压轮，精加工不锈钢材料，高性能热风机，关键部位都采取二次增强处理，所以坚固耐用，且结构简单，结构都采取模块化组件，便于维护。
该机体积小、轻巧，净重仅15公斤、拥有可调自走接驳速度和恒温的特点，操作简单，仅取决于个人操作熟练和灵活程度。
一、应用范围
LC-3000智能型：适用于广告喷绘布行业，喷绘布、灯箱布、刀刮布、网格布等PVC、PE热熔性塑料膜材的焊接加工。
二、主要技术参数
额定电压： AC110-240V 频率： 50-60Hz
功率： 1000-3000W 温度调节范围： 0-500℃
调速范围： 1-15m/分钟 产品规格： 41*25*20cm
机身重量： 15-20Kg 拼接宽度： 2-5cm
三、特点
无胶拼接、温度速度可调，带有反馈温度传感器，可实时监测控制恒温（市场上一般为调压、温度随输入市电的电压变化而忽高忽低，不恒温）。无论拼接多长画面，拼接效果不会改变。增加了风量调节旋钮，更适合于拼接厚喷绘布。
四、操作步骤
1.首先把画面拉紧拉平，对好搭接缝（2-5cm）,用胶带或胶水固定在地面上。
2.接通电源，左转手柄，直至热风嘴与胶轮处于直线状态，再右转黑色旋钮，调节速度，一般把旋钮上的标记指向2的位置，设定完毕，右旋手柄直至热风嘴与地面脱离，行走即停。
3.设定温度。打开温度开关（右旋金色旋钮听到咔嚓声即可），按▲升温，按▼降温，根据布的薄厚和耐温性设定你需要的温度，一般情况在300-350℃之间，或者取些布材，对准风嘴，立即熔化即可，绝对不能出现烧焦现象，这时的温度也就是你所设定的温度。
4.温度和速度调试好后，把机器右轮的外沿与搭接缝的外沿靠齐放置等待实际温度与你设定的温度接近时，左旋手柄直至热风嘴完全嵌入到拼接缝里，机器就自动行走了，拼接开始。
5.在拼接过程中，若出现烧焦拼接物时，首先把速度提高一点点，或者把温度设定低（二者选一）即可避免熔坏拼接物了。但是绝对不能急速调节，否则机器速度过快，造成机器无法直行，给心理造成恐慌，或者无法粘接和损坏画面。
6.使用前，根据你的材质找准温度和速度的配合参数再使用。慢了会烧坏画面，快了会粘接不牢，所以温度和速度配合至关重要。
7.拼接完毕，右旋手柄，直至热风嘴完全脱离拼接物，随即关掉温度开关（即左旋金色旋钮，听到咔嚓声即可）。但绝对不可拔掉电源插头和关闭电源，以免余热损坏散热风机，造成损坏设备，无法使用。一定待机器实际温度降至最低时，才能拔掉电源插头和总开关。
8.严禁雨天使用，工作场地要干燥，平整，注意防火，设备要专人负责，专人操作，严禁不懂乱用。设备工作电压为：110V—240V(两种)严禁私自拆机，否则后果自负。
9. 保修期一年，加热件为易损品，不在保修范围内，但有责任为您提供配件，费用自理。
10. 随机配件：10m电源线一根，备用加热件一只，说明书及光盘一套。
11.产品若有改动，厂方不另行通知，请垂询当地经销商，产品说明仅供参考，不具备合同法律
效力，最终解释权归本厂所有。
12.本厂所有产品已申请国家多项专利，商标已注册，防造必究。
五、 维修与保养
|
故障 |
排除方法 |
|
温度乱码、实际温度不显示 |
检查温控探头是否搭铁，应与风嘴保持悬空 查看探头是否断裂，检修传感器线。 |
|
不升温 |
检查发热件是否熔断，更换加热件。 |
|
无电源 |
检查接线是否牢固、保险管是否爆裂。 |
|
划伤画面 |
调整风嘴平行度，让风嘴右外侧离地面1mm |
|
速度失控 |
更换电位器（即黑色旋钮） |
|
焊接不牢 |
提高温度或降低行走速度，调整风嘴与地面的平行度。 |
Introduction
This product is for PVC, PE and other materials can be hot melt coated membrane plane designed for splicing.
When printing inkjet printers margins than the screen, you need to split after printing stitching, as well as printing are enhanced with the edge of the screen, Qian side, cable, wrapped in rope, etc., are traditionally used 502 and its derivatives glue and other adhesive means that there are many disadvantages, as follows: there is laminated slow, bonding strength is not enough, the screen easy to dirty, low efficiency, difficult to grasp and easy to operate, wasting time, when connected to large flat wide require larger workplaces. In particular, easy blistering after a period of wrinkles, resulting in uneven surface because the air temperature by the large, when the low temperature bonding effect is more unhappy.
Use no glue stitching cloth Welding Machine (referred to as Hot-air Welding Machine), can successfully resolve these many problems, remove the use of glue, save trouble and time were saved provincial venue, with either fabric, light box cloth, flails net canvas, etc., are no longer restricted to high-frequency machine platform length, as long as a relatively flat surface can heat your desktop or work at any time, for example: up to 100 meters of the joints can be a person in the space of 50 square homework .
This product is based on hot air welding technique, using principles of self-propelled hot together, after practice, after a large number of continuous improvement, high torque motor assembly machine, precision gear, heat resistant rubber rolling wheels, finishing stainless steel, high-performance hot air The key parts are taken by the second enhancement, so rugged and simple, modular structure components have been taken, and easy to maintain.
Machine is small, light, weight only 15 kg, with adjustable speed and constant self-propelled feeder features, simple operation, only depends on the individual operating proficiency and flexibility.
No glue splicing, temperature adjustable speed, with a feedback temperature sensor, real-time monitoring and control temperature (usually the market adjusted voltage, adjust the wind speed, temperature is not constant). No matter how long screen,welding screen effect will not change
Ⅰ、Field of application
LC-15 smart type: Suitable for advertising industry, inkjet fabric, inkjet fabric, light box cloth, Knife cloth, mesh cloth PVC, PE hot melt plastic membranes welding process.
Ⅱ、Main technical details
Rated voltage: AC110-240V Frequency: 50-60Hz
Power: 1000-3000W Temperature scope: 0-500℃
Speed scope: 1-15m/min Sepcification: 41*25*20cm
Weight: 15-20Kg Splicing width: 2-5cm
Ⅲ、Characterics
No glue splicing, temperature adjustable speed, with a feedback temperature sensor, real-time monitoring and control temperature (usually the market adjusted voltage, adjust the wind speed, temperature is not constant). No matter how long mosaic images,welding mosaic result will not change. With seting up a air flowing switch,it welds thick pvc easyily.
Ⅳ、Operation procedures
1、 First of all,lighten up the spraying cloth, target the sew.(2-5cm),and fix the cloth on the ground with glue or tape.
2、 Insert the power(picture),turn the handle to the left,till the spout is straight-line with the wheel.The turn the black button to the right ,adjust the speed, usually put it on 2.After adjust the speed,turn the handle to the right till the spout leave the ground.Then it stops.
3、 Adjust the temperature.Turn on the temperature button(turn the golden button to the right,it make the voice “Ka”.Then press the temperature up▲and down▼button,adjust the temperature according to the thickness and durable of the cloth,usually put it between300℃and350℃.Or you can put some materials in the spout,if the materials melt immediately and shouldn’t scorch.It is the proper temperature.
4、 After adjust the temperature and speed,put the edge of the right-wheel in a level with the edge of sew.When the actual temperature reach to your set temperature,turn the handle to the left till the spout insert into the sew totally.The machine beginstowalk.Splicing begins..
5、 During splicing,if the spout melt the spraying cloth. Fist you should turn black button to the right a little,or you can turn down the temperature.(choose one from the two ways) in that way,it won’t melt the cloth.But you shouldn’t turn the button in very urgent speed,or it will make the machine can’t weld or damage the cloth.
6、 Before using,please find a proper temperature and speed.If slow,it will damage the cloth;if fast,it may stick not so fasten,so it is important to adjust the temperature and speed.
7、 On the completion of splicing ,turn the handle to the right ,till the spout leave the spraying cloth totally.At this time,you can turn off the temperature button.But you couldn’t turn off the power cord and the power button, in case the heat damage the heat gun,and make the machine couldn’t work.You must wait till its actural temperature reach to the lowest.
8、 Don’t use the machine in wet weather.The working place must be dry and flat.Pay attention to the fire, the machine should have technical person to operate. The working voltage is 110V-240V(two types) To open the machine,you should be responsible for the result yourself.
9、 The warranty period is six months,heating elements are not in the warranty scope due to it being a repid-wear article,and we are only responsible for the supply of fitting,but the cost is subject to the client.
10、 Fitting equipped along with the machine include a source line of 10m,a piece of alternate heating element,a instrution book and a CD.
11、 we won’t notify if the products have some change.Please tell the agents in local area, the introduction is only for reference,don’t have legal effect.The factory has the final interpretation.
12、 All the products of this factory have applied the national patents.And the trademark has been registered,no copy allowed.
Errors and methods to solve
|
Errors |
Methods to solve |
|
The temperature screen cnt’t display or garbled |
Test if the temperature probe have link with iron,please keep it in the air between the spout;test if the probe is damaged,test the sensor wire. |
|
Don’t heat |
Test if the heater is damaged,change heater |
|
No power |
Test if the link is fasten |
|
Damage the cloth |
Adjust the spout to make it flat and leave its right-edge 1mm with the ground. |
|
Speed out of control |
Change the speed button(the black button) |
|
Couldn’t weld very fasten |
Speed up the temperature or slow down the speed,adjust the level between the spout and ground. |
相关产品推荐
