食品级ABS抗静电A3000TXB

厂商 ：沙泊塑料有限公司（中山）

广东 中山
  • 主营产品：
  • TPU
  • PPS
  • POM
联系电话 ：13432026331
商品详细描述

供应食品级ABS抗静电A3000TXB

LNP STAT-LOY A3000TXB is a compound based on ABS resin. Added features of this material include: Antistatic, Transparent. Bioassessed to ISO 10993.
 
TYPICAL PROPERTIES (1)
MECHANICAL Value Unit Standard
Tensile Stress, yld, Type I, 5 mm/min 380 kgf/cm? ASTM D 638
Tensile Stress, brk, Type I, 5 mm/min 270 kgf/cm? ASTM D 638
Tensile Strain, yld, Type I, 5 mm/min 4 % ASTM D 638
Tensile Strain, brk, Type I, 5 mm/min 31 % ASTM D 638
Tensile Modulus, 5 mm/min 16900 kgf/cm? ASTM D 638
Flexural Stress, yld, 1.3 mm/min, 50 mm span 550 kgf/cm? ASTM D 790
Flexural Modulus, 1.3 mm/min, 50 mm span 16600 kgf/cm? ASTM D 790
Tensile Stress, yield, 5 mm/min 37 MPa ISO 527
Tensile Stress, break, 5 mm/min 26 MPa ISO 527
Tensile Strain, yield, 5 mm/min 4 % ISO 527
Tensile Strain, break, 5 mm/min 29 % ISO 527
Tensile Modulus, 1 mm/min 1550 MPa ISO 527
Flexural Stress 49 MPa ISO 178
Flexural Modulus, 2 mm/min 1490 MPa ISO 178
IMPACT Value Unit Standard
Izod Impact, notched, 23°C 13 cm-kgf/cm ASTM D 256
Multiaxial Impact 336 cm-kgf ISO 6603
Instrumented Impact Total Energy, 23°C 203 cm-kgf ASTM D 3763
Izod Impact, notched 80*10*4 +23°C 14 kJ/m? ISO 180/1A
THERMAL Value Unit Standard
HDT, 0.45 MPa, 3.2 mm, unannealed 78 °C ASTM D 648
HDT, 1.82 MPa, 3.2mm, unannealed 66 °C ASTM D 648
CTE, -30°C to 30°C, flow 1.E-05 1/°C ASTM D 696
CTE, -30°C to 30°C, xflow 1.09E-04 1/°C ASTM D 696
HDT/Bf, 0.45 MPa Flatw 80*10*4 sp=64mm 77 °C ISO 75/Bf
HDT/Af, 1.8 MPa Flatw 80*10*4 sp=64mm 66 °C ISO 75/Af
PHYSICAL Value Unit Standard
Specific Gravity 1.09 - ASTM D 792
Density 1.08 g/cm? ASTM D 792
Moisture Absorption, 50% RH, 24 hrs 0.54 % ASTM D 570
Mold Shrinkage, flow, 24 hrs (5) 0.4 - 0.6 % ASTM D 955
Mold Shrinkage, xflow, 24 hrs (5) 0.6 - 0.8 % ASTM D 955
Moisture Absorption (23°C / 50% RH) 0.81 % ISO 62
ELECTRICAL Value Unit Standard
Volume Resistivity 1.E+10 - 1.E+12 Ohm-cm ASTM D 257
Surface Resistivity 1.E+09 - 1.E+11 Ohm ASTM D 257
Static Decay, 5000V to <50V <1 < seconds FTMS101B

Parameter
Injection Molding Value Unit
Drying Temperature 70 - 80 °C
Drying Time 4 hrs
Maximum Moisture Content 0.05 - 0.1 %
Melt Temperature 200 - 210 °C
Front - Zone 3 Temperature 205 - 215 °C
Middle - Zone 2 Temperature 195 - 205 °C
Rear - Zone 1 Temperature 180 - 195 °C
Mold Temperature 10 - 50 °C
Back Pressure 0.2 - 0.3 MPa
Screw Speed 30 - 60 rpm


标签：
相关产品推荐